Screw and barrel cleaning with dry ice blasting

The screw and barrel of an injection molding machine accumulate degraded plastic, baked-on additives and carbonized material over time. Traditional cleaning requires full screw disassembly, mechanical removal with steel brushes or chemical methods, and reassembly. Four to eight hours per cycle is normal.
Cold Jet dry ice blasting cleans the screw and barrel with less disassembly and without solvents, and it does not abrade the screw coating. This article covers how the technology works on screws and barrels and which Cold Jet machine to use.
Why mechanical screw cleaning falls short
Steel brushes and bronze scrapers remove fouling but degrade the screw coating across multiple cleaning cycles. Nitrided and chrome-plated screws gradually lose their corrosion protection and wear-resistant properties. Replacing a screw costs thousands of euros plus extra downtime.
Chemical cleaning risks leaving chemical residue inside the barrel that carries over into the next production run. For producers with strict product purity requirements, that is unacceptable.
How dry ice blasting works on screw and barrel
Cold Jet pellets accelerated by compressed air hit the screw segments and barrel bore. Thermal shock contracts degraded plastic; sublimation blows residue away. No mechanical contact with the screw coating, no chemical residue, no moisture.
For screw segments pulled out of the barrel, cleaning in a dedicated holder is possible. For the barrel interior, a directed blast gun is used. With the PCS Ultra you switch between delicate settings (for the coating) and aggressive settings (for hardened fouling) within one machine.
How dry ice releases baked-on plastic
This Cold Jet video shows the thermal shock that releases resin and caked-on plastic from tooling. The same mechanism lifts degraded material off a screw and barrel without attacking the coating.
4:46Video by Cold Jet · 4:46
Benefits for screw and barrel cleaning
- ✓No mechanical wear on the screw coating
- ✓No solvents or chemical residue
- ✓Reaches complex screw geometries (notch segments, mixing elements)
- ✓Cleans the barrel interior without full disassembly
- ✓Safe for nitrided, chrome-plated and titanium coatings
- ✓Extends screw service life
- ✓Reduces cross-contamination risk between production runs
Applications on screw and barrel components
| Component | Contamination | Cold Jet approach |
|---|---|---|
| Screw segments (removed) | Degraded plastic, resin residue | PCS Ultra in a dedicated holder |
| Screw flights (without disassembly) | Plate-out, additives | PCS Ultra with a directed blast gun |
| Barrel bore (interior) | Burned plastic, carbon residue | PLT Ultra with a guided jet |
| Injection nozzle and tip | Degraded material | PCS Ultra fine pellets |
| Mixing elements and notches | Stuck-on material | PCS Ultra |
| Pressure sensors and thermocouples | Dust, fouling | i³ MicroClean 2 |
Recommended Cold Jet machines for screw and barrel cleaning
The PCS Ultra gives the most flexibility with 28 selectable particle sizes. For heavier applications or severe degradation, switch to the PLT Ultra. For delicate dosing sensors and thermocouples, the i³ MicroClean 2 is the right choice.
Related mold cleaning applications
- ✓In-press cleaning with dry ice blasting
- ✓Blow mold cleaning with dry ice blasting
- ✓Rubber mold cleaning with dry ice blasting
Want Cold Jet dry ice blasting for your screw and barrel maintenance? Request a no-obligation demo.
Request a demo →Frequently asked questions
Can the screw and barrel be cleaned without cooling down?
For the exterior of the barrel and accessible screw segments, Cold Jet works at operating temperature. For deeper cleaning inside the barrel bore, a brief cooldown to 80 degrees Celsius can be useful. We advise per machine and plastic type.
How long does screw-and-barrel cleaning take with Cold Jet?
A full disassembly-cleaning-reassembly cycle that normally takes 4 to 8 hours can often be done with Cold Jet in 60 to 120 minutes without full screw disassembly. For deep cleaning a short screw pull is required.
Does Cold Jet also remove degraded plastic in the barrel?
Yes, degraded and carbonized plastic releases under thermal shock from the pellets. For heavy degradation multiple passes are needed; for routine maintenance one treatment per part is sufficient.
Which Cold Jet machine do you recommend for screw and barrel cleaning?
The PCS Ultra or PLT Ultra. PCS for finer control across different plastic types, PLT for heavier applications and higher pressure. Both reach complex screw geometries that are hard to access manually.
Does dry ice blasting damage the screw coating?
No, Cold Jet is non-abrasive and safe for nitrided, chrome-plated and titanium-coated screws. Our settings stay within the limits of your screw manufacturer’s specifications.
